Hasselblad 949 Instrukcja Użytkownika

User’s GuideSlide Feeder for Flextight 949 Scannersby Hasselblad

10 AB Figure 3: Back panel of the Slide Feeder, showing the electrical connector (A) and mounting pins (B).Li the batch-feeder panel on the front of

11Grasp the Slide Feeder rmly with one hand while holding the batch-scan door open on the scanner with your other hand. Align the pins and connector

12 BACD Figure 5: e Slide Feeder attached to a scanner and with its magazine drawer open, showing the original-holder supports (A), drawer hinge (B),

13 Figure 6: Inserting the Slide original holder.Position the Slide holder on the two supports extending from the front of the Slide Feeder and slide

14Click on Done to close the Feeder window.Close the magazine drawer by rotating it up and pressing it into place so that the metal clasp clicks in it

15Unmounting the Slide FeederTo unmount the feeder, you must always use the soware-guided procedure below to ensure that the scanner drum and the mag

16e Mount feeder window updates with new instructions. As instructed in the window, remove the holder from the scanner with both hands, grasping the

17e Mount feeder window updates with new instructions. Close the magazine drawer by rotating it up and pressing it into place so that the metal clas

18Loading SlidesDepending on your work load and preferred working method, you might decide to load slides directly into the Feeder, or to work using t

19Remove any slides that you have already scanned. en, starting at the front/top of the magazine, load new slides in the order in which you would lik

2© 2005 Hasselblad A/S. All rights reserved.Slide Feeder for Flextight 949 Scanners, Part No 75020088 revision B.e information in this manual is furn

20 Figure 10: Removing the magazine drawer from its hinge.Place the drawer at on a table with its magazine facing up.Using both hands, pinch the four

21Take the second magazine, which you just nished loading, and position it the same way as the magazine you just removed. At one end, the magazine ha

22Scanning with the Slide FeederBatch Scanning with 3fe Slide Feeder is intended as a tool for scanning large number of slides in a production enviro

23Instead of using the standard preview/scan workow in FlexColor, click on the 3f button to open the Scan 3f window. Make the various 3f settings as

24FlexColor to analyze each image to decide whether it is negative or positive. It will then use either the Positive Setup or Negative Setup that you

25As you work with the 3f images in the light table, you can load each image into FlexColor to make settings and then save the settings back in the hi

26Click on the Batch Scan button to open the Batch Scan window.If it is not already shown, expand the Feeder heading in the Batch Scan window by click

27 If you are using the Manual list, then continue taking previews and adding scans until you have dened all of the scans you wish to make in this ba

28TroubleshootingBelow are a few common problems and how to solve them.Problem: I am not able to mount the Feeder to my scanner.Solution: First, mak

29Solution 2: Move the drum to its home position. To do this, run FlexColor and select Maintenance > Feeder to open the Feeder window. en set the

3Table of ContentsIntroduction 4Important Warnings and Restrictions 4System Requirements 5Feeder Diagram 6Slide Original Holder Diagram 7Mounting

30Aligning the Feedere Feeder is pre-adjusted to align perfectly with most individual scanners. However, some scanners may have a drum that is aligne

31 Figure 13: Unlocking/locking the Feeder position. Two nuts hold the Feeder in place—one is visible above; the other is located on the other side of

32Preparing the Slide Feeder for Storage or TransportTo prepare the Feeder for storage or transportation:Detach the Feeder using the soware-guided pr

33Preventive MaintenanceAll Flextight scanners should be serviced every 25,000 scans or every 12 months, whichever comes rst. If a Feeder is mounted,

34Technical InformationSpecicationsScanner supported Flextight 949Scanner footprint with feeder 36 x 42 cmWeight 3.1 kgMaximum batch 50 slidesOri

35CE Declaration

36

4Introductione Slide Feeder is an optional accessory for Flextight 949 Scanners. It enables you to use your scanner to load individual slides and to

5Install the scanner and Slide Feeder in a location where they are not accessible by children. e units contain small openings and moving parts that c

6Feeder DiagramACDFBEG Figure 1: Features of the Slide FeederMagazine drawer clasp: holds the drawer closed; to open the drawer, pull here and swing d

7Slide Original Holder DiagramACDEFB Figure 2: Slide original holder featuresLoading tab: is tab must face into the scanner. A magnet inside the scan

8Mounting and Unmounting the Slide Feedere procedures for both mounting and unmounting the Feeder to/from your scanner require that you use the sowa

9Select Maintenance > Feeder from the FlexColor menu bar. e Feeder window opens. Click on the Mount button. e Mount feeder window opens, which g